4BHS
Borehole
4″ submersible centrifugal electric pump made entirely of AISI 304 stainless steel. Suitable for coupling with NEMA-compliant motors. The discharge casing and the motor support are made of molded stainless steel. Support, openings, joint, impeller, diffuser, valve, stages, tie rods and cable cover in EN 1.4301 (AISI 304). The shim ring in EN 14.301 (AISI 304) + EPDM while the shaft in EN 1.4401. Radial bearings, axial bearings and thrust bearing are made of tungsten carbide. Suitable for domestic, agricultural and industrial water supply systems, pressurisation systems, for fire-fighting, irrigation, washing for and clear water movement in general.
PUMP TECHNICAL DATA
- Total head from 9 to 260 m
- Capacity from 0.9 to 18 m3/h
- Maximum immersion 350 m (water filled motor) 150 m (oil filled motor)
- Maximum liquid temperature 30°C
- Maximum sand content 50 ppm
- Maximum chlorine content 500 ppm
- MEI > 0.4
4WN
Borehole
4” borehole centrifugal pumps with floating Noryl impellers and glass fibre reinforced polycarbonate diffuser for a particulary resistant configuration. Equipped with a non-return valve, coupling joint and filter grid in stainless steel. Easy installation for borehole pumps equipped with motor (oil or water filled). Suitable for horizontal operation. Particularly recommended for the movement of clear water in wells, the pressurisation of clean water for agricultural, domestic or industrial use, or for the irrigation and movement of water in general.
TECHNICAL FEATURES
- Total head up to 289 m
- Capacity up to 24 m3/h
- Maximum liquid temperature 35°C
- Maximum sand content 150 gr/m3
- MEI > 0.4 for all models
- Protection degree IP68 (for oil filled motor and water filled motor)
6BHE(L)
Borehole
6” submersible centrifugal pump
6″ submersible pump, stainless steel AISI 316 AISI 304 (6BHE) and (6BHEL), for deep wells. Discharge casing, impeller, stages, support and diffuser are in AISI 304 or AISI 316 depending on the model. The shaft is in AISI 431 for 6BHE and AISI 316 + AISI 329 for 6BHEL. They can be used for water supply from deep wells, for water distribution and pressurisation, irrigation systems, water treatment, filtering and reverse osmosis, industrial cooling systems, fountains and fire-fighting systems.
PUMP TECHNICAL DATA
- Total head from 8.2 to 700 m
- Capacity from from 6 to 80 m3/h
- Maximum immersion: 350 m (water filled motor) 150 m (oil filled motor)
- Maximum liquid temperature 60°C
- Maximum sand content 100 gr/m3
- MEI > 0.4 (for all models except 6BHE (L) 13)
The pump and the motor are supplied separately.
Note: 6BHE(L) 13 not available for the European Market.
8BHE(L)
Borehole
8” submersible centrifugal pump
8″ submerged centrifugal pump, for semi-axial flow deep wells, in stainless steel AISI 304 (8BHE) or AISI 316 (8BHEL). Developed specifically for high flow pumping needs. Discharge casing, stages and support in AISI 304 or AISI 316 depending on the model. The shaft is in AISI 329 and the impeller in AISI 316. They can be used for water supply from deep wells, for water distribution and pressurisation, irrigation systems, water treatment, filtering and reverse osmosis, industrial cooling systems, fountains and fire-fighting systems.
PUMP TECHNICAL DATA
- Total head from 8.2 to 450 m
- Capacity from from 6 to 126 m3/h
- Maximum immersion: 350 m (water filled motor) 150 m (oil filled motor)
- Maximum liquid temperature 60°C
- Maximum sand content 100 gr/m3
The pump and the motor are supplied separately.
DIRECTO 1-2
Control systems and panels
Electrical control panel for submersible or submersible pumps and pressure boosting systems with surface pumps.
- Electronic control panel for one single phase or three phase pump. (DIRECTO 1)
- Electronic control panel for two single phase or three phase pumps with exchange function and emergency function integrated. (DIRECTO 2)
DIRECTO is equipped with indicator lights for power on, thermal trip and engine running, a manual or automatic switch, a mains switch interlocking door.
A terminal block allows connection to the external commands such as pressure switches, floats etc.
E-SPD
Control systems and panels
E-SPD is an air-cooled inverter, which can be installed directly on the terminal box, designed to control the start and stop of the pump based on the setpoint of the system pressure. It offers high energy savings and reduced noise levels, along with operating costs. It can be used in residential applications as it conforms to Directive EN 61800-3 Category C2.
TECHNICAL FEATURES
- The inverter installation is user friendly with quick set up which ensures a fast and effective start up.
- It can be adapted to all centrifugal pumps, both horizontal and vertical
- The LCD display allows effective management of all system parameters, including a back-up history
- The E-SPD can protect the system against overpressure, over current, voltage fluctuation, dry running and water leak
- The E-SPD comes equipped with 2 digital inputs and 2 relay outputs in addition to pressure transducer input (4-20 mA).
- The E-SPD is also RS485 compliant which enables connection of up to 8 inverters
TECHNICAL DATA
- Main supply: single-phase 230V, three-phase 400V;
- Motor output (pump): three-phase 230V/400V;
- Output current: 11A;
- Frequency: 50-60 Hz (+/- 2%);
- Max ambient temperature: 40°C;
- Insulation class: F;
- Protection degree: IP55
IDROGO
Borehole
External casing, motor cover, shaft, seal housing disc, filter and closing ring in AISI 304 Impeller, diffuser and spacer in PPE+PS reinforced with fibreglass Upper mechanical seal (motor side) in Carbon/Ceramic/NBR while the lower one (pump side) in SiC/Carbon/NBR Movement of clean water from wells, cisterns and tanks, the pressurisation of domestic systems, small irrigation, the washing of vehicles and increases in pressure in general.
PUMP TECHNICAL DATA
- Total head from 10 to 76 m
- Capacity from 1.2 to 7.2 m3/h
- Maximum immersion 2m (with cable lenght 5m), 10m (with cable lenght 20mt and with float switch version), 17m (with cable lenght 20mt)
- Maximum liquid temperature 40°C
- Maximum solid size passage 2.5 mm
PRESSCOMFORT
Control systems and panels
PRESSURE REGULATOR
PRESSCOMFORT is an automatic electronic appliance, destined to regulate functioning of the electric pumps without using booster reservoirs. This unit manages the automatic start and stop of the pump when opening or closing any tap or valve of the installation. When the pump starts, it keeps running while it exists any tap opened in the system, giving flow and pressure to the hydraulic net while ther is demand. If there is no suction air, the pump stops automatically.
PRESSCOMFORT allows:
- manual restore (RESET key)
- automatic restore after 1, 6, 12 o 24 hours.
If on suction the water returns to a pressure exceeding the fixed value (1.5 bar) for pump start-up, PRESSCOMFORT is restored automatically.
TECHNICAL DETAILS
- The PRESSCOMFORT is replacing the traditional expansion tank, pressure switch, check valves, level switch.
- Version with or without cables
- Automatic regulation
- Adjustable start-up pressure
- Incorporated non-return valve
- Plate with functioning indicator
- Connection cable on the pump terminal box (for wired version only)
- Power supply cable (1.5 m) with standard socket (for wired version only)
TECHNICAL DATA
- Maximum temperature of the water: 60° C
- Maximum flow rate: 10,000 l/h
- Start-up pressure: 1.5 – 2.5 bar
- Maximum use pressure: 10 bar
- Power supply voltage: 220V±10% – 50/60 Hz
- Maximum current intensity: 10A
- IP65 Protection rating
- G1 connections (pump and outlet side)
Q SERIES
Control systems and panels
ELECTRIC CONTROL PANELS FOR SUBMERSED ELECTRIC PUMPS
The protection and control board for a submersed single phase electric pump. The control panel is composed of a box in ABS with IP54 protection rating and allows to control an electric motor with single phase power supply. Thanks to the presence of a circuit breaker protection, it ensures the interruption of motor functioning in the case of over currents.
TECHNICAL DETAILS
- Controlling the electric pump via the luminous bi-polar switch
- Motor protection via thermal cut-out with manual reset
- Housing inside the capacitor for motor start-up.
SB3
Borehole
Casing, discharge casing and motor joint are in AISI 304. Polyacetal resin POM diffuser. Impeller in PPO, glass fibre reinforced polymer. Especially recommended for the movement of clear water in wells, the pressurisation of clean water for agricultural use, industrial use and for the irrigation and pumping of water in general.
TECHNICAL DATA
- Total head from 9.8 to 122 m
- Capacity from 0.6 to 2.7 m3/h
- Maximum immersion 60 m
- Maximum liquid temperature 30°C
- Maximum sand content 50 ppm
SERVOPRESS
Control systems and panels
PRESSURE REGULATOR
SERVOPRESS is an automatic electronic appliance, destined to regulate functioning of the electric pumps without using booster tanks. This unit manage the automatic start and stop of the pump when opening or closing any tap or valve of the installation. It keeps pump running while it exists any tap opened in the system, ensuring flow and pressure to the hydraulic net while ther is demand. Morevoer, it guarantees dry running protection and anti-blocking functionalities.
SERVOPRESS allows:
- setting of re-starting pressure by dedicated button (SERVOPRESS LP SET M)
- reading of re-starting pressure directly by display
- anti-blocking and automatic restart functionalities
- TUV certification
- It can be mounted on surface pumps and submersible pumps
TECHNICAL FEATURES
- The SERVOPRESS is replacing the traditional expansion tank, pressure switch, check valves, level switch
- Version with 115/230V power supply voltage
- Automatic set up
- Adjustable start-up pressure (for SERVOPRESS LP SET M version)
- Incorporated non-return valve
- Display for functioning visualization
- Dry running protection
- Anti-lock system
TECHNICAL DATA
- Maximum temperature of the water: 65°C
- Minimum low rate: 10.000 l/h
- Start-up pressure:
- 1,5 bar Servopress LP 1,5 BAR
- 2,2 bar Servopress LP 2,2 BAR
- 1,5 – 2,2 – 2,5 BAR Servopress LP SET M
- Maximum use pressure: 12 bar
- Power supply voltage: 115/230V – 50/60 Hz
- Maximum current intensity: 16(8)A
- IP65 protection rating
- G1 connections
SF6
Borehole
code 106
6” submersible centrifugal pump
Discharge and suction casing in cast iron. The outer casing, the spacers, the shim rings, the nonreturn valve, the cable protection and the suction grid in AISI 304. The impellers and diffusers in PPO reinforced with glass fibres. The shaft is in AISI 420. Suitable for water supply systems for civil and industrial use, for pressurisation systems, for irrigation, aqueducts for communities.
TECHNICAL DATA
- Total head from 7 to 362 m
- Capacity from 3 to 66 m3/h
- Maximum liquid temperature 30°C
- Maximum sand content 50 ppm
- MEI > 0,4 per SF6 R10
- MEI > 0,6 per SF6 R13
Note: SF6 25, SF6 32, SF6 42 not available for the European Market
SMART EVO 1-2
Control systems and panels
Electronic control panel for sewage and pumping systems.
Electronic control panel for one single phase or three phase pump. (SMART EVO 1)
Electronic control panel for two single phase or three phase pumps with exchange function and emergency function integrated. (SMART EVO 2)
SMART EVO is equipped with LED lights signaling voltage presence, thermal protection and motor running, a main switch interlocking door, pushbuttons for manual or automatic operation, level relay for probes volt free alarm contacts. The external controls such as float switches and pressure switches are connected to the terminals of the main electronic board.
STARTDELTA 1-2
Control systems and panels
Electrical control panels for starting centrifugal pumps or pressure booster systems with surface pumps.
Electromechanical control panel for one three phase pump.
Star/Delta start. (STARTDELTA 1)
Electromechanical control panel for two three phase pumps with exchange function emergency function integrated. Star/Delta start. (STARDELTA 2)
STARDELTA reduces the current and the starting torque to 33% (1/3 of a direct start).
SUBMERSIBLE MOTORS FOR BOREHOLE PUMPS FROM 3”-4”-6”
EBARA Submersible motors
EBARA motors offer a huge range of submersible motors for well, oil filled or water filled version.
From to 3” up to 6”, compact dimensions, reliability and high performance make this range completely and performing in every installations. All EBARA motors are available with standard NEMA connections.
WINNER 4N
Borehole
4″ submersible centrifugal electric pump in AISI 304 with floating impellers with frontal shim. The outer casing, the shaft and the valve are in AISI 304. Discharge casing in EN 1.4308 (ASTM CF8). The impeller is in Ixef® (glass fibre reinforced thermoplastic) for the 4N1 – 4N2 – 4N4 – 4N7 models, in glass fibre reinforced polycarbonate for the 4N10 – 4N15 models, PPE+PS diffuser reinforced with glass fibres. Particularly recommended for the movement of clear water in wells, the pressurisation of clean water for agricultural, domestic or industrial use, or for the irrigation and movement of water in general.
PUMP TECHNICAL DATA
- Total head from 6.2 to 370 m
- Capacity from 0.6 to 21 m3/h
- Maximum immersion 350 m (with water filled motor)
- 150 m (with oil filled motor)
- Maximum liquid temperature 40°C
- Maximum sand content 50 ppm
- Maximum chlorine content 500 ppm
- MEI > 0.4
















